2010年,加州霍桑。一栋旧厂房改造的办公楼里,SpaceX 只启用了三层中的第一层。每层能坐 300 人,大开间,没有隔断墙。马斯克的工位就在这片开阔区域里,销售副总裁的工位也在。
同一栋楼里往车间方向走,温度会突然降下来。那是一个把室温固定在 68 华氏度(约 20 摄氏度)的房间,里面摆着一台三坐标测量机,负责把零件量到千分之一英寸(约 0.025 毫米)以内。
这一年,SpaceX 造出的火箭发动机数量,比全美其余所有公司的产量加起来还多。按马斯克的说法,下一年他们会造得比世界上任何一个国家都多。
这趟参观是马斯克本人带着镜头走完的,从大堂一路走到机加工车间,中间经过服务器机房、任务控制室、检测间、振动台、电磁干扰测试室、复合材料车间和贮箱焊接区。信息密度很高,每一站都能看到一个具体的管理判断。
门是沟通的天敌
参观从大堂开始。墙是白的,马斯克说以后会加一些装饰,现在看着有点空。
办公区采用彻底的开间式布局,目的写得很直白:最大化沟通。他特别解释了一句,公司里除了人力资源和财务的少数人,所有人都在格子间里,包括各位副总裁。
这句话背后有个判断:门会限制沟通。所以 SpaceX 刻意压缩独立办公室的数量,能不开就不开。
马斯克自己认同这种透明性带来的好处。站在开间里,你能看见别人电脑屏幕上在做什么。镜头扫过去,一位工程师正在整理 Draco 推进器的装配文档。Draco 是龙飞船用的姿控推力器,这个人负责它的研制推进。桌上摆着一小段试制的喷管锥体样品。
这种“顺便看一眼就知道同事在干什么”的状态,是开放式布局最直接的收益。它不需要开会,不需要发邮件,不需要预约。
换个角度看,这种做法把沟通从一件需要主动发起的事情,变成了一件被动接收的事情。你不用决定去问谁,信息自己会飘到你眼前。代价是噪音和缺乏隐私,收益是决策链条短。
一面会变暗的玻璃,一群被记住的名字
会议室有一面通高的玻璃墙。人走进去,运动传感器触发,玻璃自动变成不透明。
会议室没有编号,每一间都用一位伟大火箭工程师或空间科学家的名字命名。马斯克说,这些人值得被记住,是他们让人类成为跨行星物种这件事有了技术基础。公司里也有以宇航员命名的房间,但重点还是放在真正设计火箭的人身上。
这个细节能看出一家公司的价值排序。命名权给谁,注意力就流向谁。把房间挂在工程师名下,等于每天提醒所有经过的人:这里崇拜的是把东西造出来的人。
再往里走是服务器机房。大约 500 个处理器,主要跑三类任务:计算流体力学、有限元分析,以及 3D 实体建模的存储。马斯克感慨了一句,现代算力让小空间里塞进这么多处理器成为可能。这句话放在 2010 年听,语气里有明显的惊叹成分。
任务控制中心和发射控制中心当时还在施工。规划里有两块巨大的影院级屏幕,可以合成一整幅画面,也可以切成四块分别显示。地面会做成底下打光的玻璃砖,工位带蓝光。马斯克带着镜头描述这些的时候,语气跟介绍一台机床差不多,很平静。
68 华氏度,千分之一英寸
检测区是整趟参观里温度变化最明显的一段。马斯克走进这个房间,第一句话就是“温度一下子降了好多”。
原因很简单:金属会随温度膨胀和收缩。要做精密测量,环境温度必须锁死。这个房间常年维持在 68 华氏度,就是为了量得准。
旁边一台设备正在工作,任务是把零件检测到千分之一英寸的精度,确认它是不是按照设计被加工出来的。
这里有一条贯穿全公司的原则:能 3D 设计就 3D 设计,能 3D 制造就 3D 制造,能 3D 检测就 3D 检测。目的是尽量减少 2D 和 3D 之间的来回转换。马斯克补充说,偶尔有些东西用 2D 表达更清楚,但绝大多数情况下 3D 更好。
这条原则听起来像技术偏好,实际是成本控制。每一次格式转换都是一次信息损耗的机会,也是一次返工的机会。设计图上的一根管子,转成二维图纸再交给车间,车间再凭图纸理解成三维实物,中间任何一环理解偏了,出来就是一个废件。一枚火箭上有成千上万个零件,这个概率会被放大成灾难。
让火箭“以为自己正在飞”
航空电子测试区里摆着两套数学模型:猎鹰 1 号一级发动机的,和二级发动机的。
更关键的是一套硬件在环仿真系统。飞行计算机、航电设备、舵机都接在真实硬件上,但从这些设备的角度看,它们就是在驾驶一枚真的火箭飞向太空。系统跑完一遍,工程师再核对:该做的动作是不是都做了,火箭能不能安全入轨。
这种做法把大量问题在实验室里就暴露出来了,不用等到发射台上。发射台一天的等待成本,可能比这套测试系统一年的电费还高。
旁边一排是热循环试验箱。零件要被扔进去跑 50 个温度循环,确认它扛得住。马斯克解释为什么太空环境比地面严酷得多:太空里没有空气帮你把温度摊平。一个零件可能一边被太阳直晒,一边处于最深的黑夜,两面温差极大。地面上有空气对流,温度相对均匀,太空里没有这个缓冲。
再旁边是热真空循环设备,温度和真空一起上。真空环境还有个副作用,散热只能靠辐射,没法靠对流。地面上一块芯片过热,加个风扇就行;太空里只能靠导热板把热量导出去,设计思路完全不同。
最容易坏的时刻是起飞
振动间里立着两台振动台,一大一小。它们模拟的是火箭起飞时那种极其剧烈的声学和振动载荷。
马斯克说了一句很实在的话:东西最容易坏的地方,就是起飞那几秒,比任何其他环节都更容易出问题。
这话对做硬件的人应该很有共鸣。所有静态测试都过了,所有仿真都收敛了,最后败在一声巨响带来的随机振动上。一个焊点、一根线束的固定夹、一颗螺钉的防松措施,在静力学分析里全是无关紧要的细节,在起飞瞬间全是主角。
紧挨着的是电磁干扰测试室。马斯克自己都承认,这房间看着有点像刑讯室。它的用途是把火箭或飞船的舱段放进一个有天线阵列的封闭空间里,验证十几台无线电设备之间不会互相干扰。
一枚火箭上通常有十几台收发设备,要么发射要么接收,频段各不相同。它们必须能同时工作,还得保证发出去的信号能被地面稳稳收到。这件事没法靠计算保证,只能实测。尤其是接收端,一个微弱的干扰信号就可能把下行遥测毁掉,而这恰恰是判断飞行是否正常最重要的通道。
一个装得下公交车的整流罩
镜头转到一个巨大的弧形结构上。这是猎鹰 9 号整流罩的四分之一段。
尺寸值得记一下:直径 17 英尺(约 5.2 米),长度 50 英尺(约 15 米)。马斯克说,这个整流罩真的能装下一辆城市公交车。它能容纳世界上最大的卫星。
材料是碳纤维,非常轻。马斯克的说法是,它大概是同类产品里最轻的承力结构,靠的是最先进的分析手段去优化质量分布。
注意这个逻辑:轻的原因在于算得足够细,每一克不必要的重量都被优化掉,偷工减料从来不在选项里。结构优化能力本身就是产品竞争力。同样一个整流罩,做得重一点也能用,但重出来的每一公斤都在吃掉运载能力,最后换算成客户的发射单价。
龙飞船的压力容器,此刻倒着放
龙飞船的装配区里,压力容器主体已接近完工,还差前后两个端盖的封头。它现在倒扣着,所以镜头里能看到主舱门、几个舷窗,还有用来对接空间站的通用对接机构。
马斯克特意说明,这一个是真正要飞的产品,会走完整的鉴定测试流程。隔壁那一个是工程测试件,虽然外形相似、同样是焊接结构,但用途完全不同:它是用来摸索“龙飞船到底该怎么造”的探路件。
这段话里有个容易被忽略的区分:工程测试件和飞行件是两条线。前者允许失败,允许反复改;后者一旦开焊,每一步都得留痕。把这两种东西混在一起管理,最后的结局通常是飞行件带着一个没人敢确认的隐患上天。
防热大底用的是 PICA,全称酚醛浸渍碳烧蚀材料。马斯克的评价很直接:这是你能拿到的最好的防热材料。旁边的工程测试件就是为这种材料的成型工艺探路的。
车间里还能看到空间站对接机构的金属环实物,龙飞船那一侧也有一个,只是导向叶片这版还没装。此外还有舷窗、易碎螺母、结构加强隔框,以及一个用来测定溅落载荷的小模型。溅落是个瞬时冲击事件,模型的作用是在水池或者落震台上先把载荷摸清楚,省得真飞船掉进海里才第一次知道要承受多大应力。
贮箱的三个编号,藏着整个研制节奏
东侧的高跨厂房(high bay)用来做猎鹰 9 号的贮箱,现在也临时当仓库用。厂房下面一片区域是贮箱焊接工位,镜头里能看到好几节筒段。
马斯克报出三个编号,把整个研制节奏说清楚了:
- 1 号贮箱是测试贮箱,已经在得州的试车台上
- 2 号贮箱是鉴定贮箱,已经完成
- 3 号贮箱正在地面上以筒段形式待焊,它将是第一个真正上天的飞行贮箱
三件产品,三种身份。测试件用来试错和摸边界,鉴定件用来证明设计达标,飞行件才承担发射任务。这个分法看着朴素,实际是硬件研制的骨架。很多项目出问题,就出在这三类件被混着用。经费紧张的时候,“反正长得一样,先拿去试一下”是最常见的事故开端。
厂房里还有一个巨大的旋压成型工具,用来把两段焊接好的锥体旋压成球形轮廓。材料可能是铌合金这类难熔金属。为什么要旋?马斯克解释,球形轮廓是让火箭推力效率最大化的最优形状。
另一个气候控制车间里,摆着制造复合材料件用的巨型芯模。它负责成形猎鹰 9 号的级间段、龙飞船的货舱段、推进段裙,以及任何直径在 12 英尺以内的筒体件。等旁边的复合材料制备间装修完,这些活儿会整体挪过去。
猎鹰 1 号的结构装配也在这一片。能看到二级鼻锥、鼻锥成形工装、有效载荷适配锥、级间段芯模。马斯克顺口提了一句:猎鹰 9 号的级间段就是猎鹰 1 号级间段的放大版。这句话透露的思路很清楚,先用小火箭把构型验证一遍,放大再飞一遍,能不重新发明的就不重新发明。
猎鹰 1 号的飞行节奏也在这里:第五飞已经在发射场待命,四飞大约三四个月后发射,五飞排在次年上半年。他说希望那趟能带上客户载荷。
80% 的价值自己造
机加工车间里有大约 30 台各种规格的设备,包括线切割电火花机床。马斯克说,为了造出一枚火箭,这里有数量惊人的金属被“雕刻”出来。
然后他给出这趟参观里最有分量的一个数字:SpaceX 按价值算,大约 80% 的飞行器是自己造的。
这句话的含义超出“垂直整合”四个字。金属进来,发动机出去,中间所有环节都在自己手里。一个零件进来时是锻件,经过车、铣、钻、切,最后变成发动机的燃烧室衬里。衬里上的冷却槽和冷却孔,就在车间里加工。
车间里能看到发动机喷管、燃烧室、喷管与燃烧室之间的集合器、级间结构件、发动机结构件,还有给猎鹰 9 号主氧供应用的管件。有些东西属于专有工艺,镜头一带而过,但已经足够说明问题。
弯管区有自动化弯管机。一根弯成麻花状的复杂管路,只要程序编好,机器每次都能弯出一模一样的东西。一枚火箭里有大量管路,靠手工一根根弯,一致性问题无解。这种设备的价值不在快,在稳定。第一百根和第一根必须完全一样,否则后期的装配公差会被越叠越大。
发动机厂房里摆着两种梅林喷管。真空版喷管展开面积更大,海平面版是较短的铜制喷管。旁边是猎鹰 9 号的推进剂供应管路:一个贮箱分流出九台发动机,再加上加注和泄出管路,总共 10 组 5 英寸(约 12.7 厘米)直径的管线。
马斯克打了个比方,这就像一台九缸发动机的汽车。这个比喻挺妙,因为九缸发动机的难点从来不在缸数,在于如何保证九个缸的进气、点火、输出完全同步。火箭上这个问题更极端,九台发动机的推力如果不平衡,箭体就会在起飞段被生生扭出一个弯矩。
有一台梅林 1C 刚刚完成全部流程,是第九台也是最后一台要运往得州参加九机并联点火的发动机。马斯克对那次试车的评价是“会相当壮观”。
一年造的发动机比所有人都多
把上面这些串起来,才能理解马斯克那句产量宣言的分量。他说,光是这一年,SpaceX 造的火箭发动机就比全美其余所有公司的产量加起来还多;明年,他们会造得比世界上任何一个国家都多。
这个数字只有放在“80% 自造 + 30 台机床 + 自动化弯管 + 完整测试链”这套体系里才成立。它反映的其实是把研发、制造、测试的反馈回路压缩到最短的能力。别人改一版设计要等供应商排产,他们改一版当天就能重新加工出来,第二天就能上试验台。
猎鹰 9 号是美国现役最强的单芯级火箭。等两三年后重型猎鹰首飞,它会是全世界最强的火箭,因为到那时航天飞机已经退役。马斯克给的类比很直观:推力相当于一架空客 A380 或者波音 747。
猎鹰 1 号和猎鹰 9 号的发动机差别其实不大。区别主要在结构:猎鹰 1 号用的是密封的金字塔形结构,级的阀门都塞在金字塔里;涡轮泵、燃烧室、喷管这三样核心件,两型之间改动很小。
这种设计的延续性本身就是一种成本优势。一款发动机的工艺被验证过,放大之后大部分工艺还能用,供应链、工装、检测方法都能继承下来。真正的开销往往不在图纸上,而在那些没写在图纸上的东西里。
参观快结束时路过茶水间。免费零食和饮料,马斯克说这在航天圈里算不常见,但道理很朴素:有人加班到很晚,饿了,手边就该有东西吃。
最后他说,这只是总部,外面还有得州的试验场、卡纳维拉尔角的发射工位、夸贾林环礁的发射场,公司正在招各种人,有兴趣就投简历。
几点可以直接拿走的判断
- 把沟通成本当成一项设计指标来管。少开办公室、把副总裁放进格子间、会议室墙用可调光玻璃,这些做法跟装修喜好无关,它们都在物理层面缩短信息传递路径。如果你的团队开始频繁抱怨“不知道隔壁组在做什么”,先看座位和空间怎么排的。
- 把测量环境固定下来再谈精度。68 华氏度跟舒服没关系,它存在的理由是让千分之一英寸这个精度指标能够成立。任何做精密制造的组织,先确认测量环境可控,再谈公差。
- 减少 2D 与 3D 之间的往返。设计、制造、检测都走同一套三维数据,等于砍掉两次信息失真。落地动作很具体:把检测设备的三维输出接回设计流程,让测量结果直接跟模型比对,别停留在二维图纸会签。
- 用硬件在环仿真把飞行问题搬回实验室。让真实的航电设备以为自己正在飞,比在发射台上发现问题便宜几个数量级。任何有控制系统的硬件项目,都值得先建这个回路。
- 优先攻起飞段的振动与声学载荷。马斯克说得很明确,那是东西最容易坏的时刻。测试资源有限时,先花在这里,先把线束固定、连接器锁紧、焊点可靠性这些不起眼的细节过一遍。
- 把测试件、鉴定件、飞行件分开编号管理。三个贮箱三种身份,这条纪律能防止“用测试件凑合上天”的事故。至少做到每一步都有编号可查,谁动了哪一件能追溯。
- 用“按价值算的自制率”来评估你的护城河。80% 这个数字比任何战略叙事都诚实。算一下你的产品里,按价值计算有多少是别人做的,你就知道自己真正掌握的是什么。自制率低于某个阈值,你的交付节奏其实握在别人手里。
- 看实际交付量而不是声量。想判断一家硬件公司处在什么阶段,看它一年实际交付多少台核心部件,比看它发了多少条通稿有用得多。
0:00[Music] welcome to SpaceX here in the lobby it's very white right now but there are actually some some cool elements coming in soon that will make it less light in the front of the building we have our engineering offices and space for about 300 people per floor and we've got a total of about three floors that we can open by not only the first floor is occupied we're accredited personally which is a very open plan to maximize communication and make it sort of fairly nice-looking this place used to be quite dismal that's that's my office over there actually we really try to minimize the number of offices that we have because doors limit communication
0:46everyone company with the exception of a few people in like HR and Finance actually are in cubes including your vice president's over there this grin at her cue I'm responsible for sales I'm in charge of making sure that there's revenue here in the company and we're working on lots of someone doing stuff in my deals and drying a deal so it's just a little area where people can meet and I have two written prompt your meeting was to be also very open I think
1:20it's actually quite helpful to have this openness because then you can sort of see what people are working on their computers like what that mccune here is is doing what are you working on there making a assembly documentation or the Draco okay RCS David is is but driving the development of our in space thruster for Draco and if there's a little piece of it or xx just attempt that's just a sample spun cone yeah we don't want X
1:56this testing how to facility down there got a vacuum system so kind of back forth and riders along right says the direct engine is what is used in our Dragon spacecraft and also in the other stage of of Vulcan nine for orbital maneuvering and reentry but this is our meeting room meeting room full when we meet with our customers and it's be a CEO of a customer comes to fear or something like that it's kind of cool because it's got this glass that that goes up Paik and we put a motion sensor on it so as you walk in the glass goes opaque we named our copper frames after the great rocket engineers and great scientists related to space so we think
2:41they really deserve the credit for you know enabling us to become a spacefaring civilization so we're fairly science and engineering centric we have some some property was named after astronauts too but we try to focus more on the people that actually design both rocket but that's where we have our server room which has I think a similar in order of 500 processors for computing I think computational fluid dynamics finite element analysis and obviously all about service storage for our 3d solid modeling and that kind of thing it's amazing how many processes you can get us in a small space these days with modern computing over there this is under construction but this is where our
3:33mission control and launch control will be so there's two mentioned like two big cinema screens that's one of them that's another one over there in the back and we can either have one giant image or we can have four smaller images so this whole thing is going to get laid out and there's gonna be a glass tile floor which is illuminated from below and these cool desks with kind of blue lights it'll look really pretty pretty neat so this area is where we do all of our inspection and it's climate-controlled and particularly controlled so because metals expand and contract at different temperatures so we always want to make the show this room is that exactly 68 degrees for doing our
4:12precision minute measurement and wherever possible we try to design apart in 3d to manufacture it in 3d and then to inspected in 3d so we minimize the number of 2d or 3d conversions occasionally somethings better in 2d but mostly it's better in 3d so here we are in its temperature just went down a whole lot because we're in our precision control area and what that machine is gonna do is it's going to inspect that part down to within thousandths of an inch to verify that everything was machined as it should have been so what we have here is this is a that's a math simulator of the Falcon one first stage engine that's the math simulator the second stage engine over there
4:54and we have what's called a full hardware in the loop simulation of the vehicle so from an avionics electronic standpoint from a steering standpoint the flight computer avionics think that they're flying the vehicle to space and then we verify that they've done all the computers actually done all the things are supposed to do to to make the rocket get successfully to space so here in our avionics test facility that's what we do test avionics market size and shapes so if we carry a bunch of thermal cycling chambers that'll take parts and put them through via 50 thermal cycles clarify that things are gonna be okay and the temperature environments in space is
5:34much worse than the ground because you don't have the you know things you don't have air to even out the temperature so you could actually hex up something could be in searing Sun lights or blackest nights and it's gotta be able to handle much more of a temperature range than it would on earth that's a thermal vacuum cycler so it'll test both it'll test that part in vacuum going through the temperature cycles that's how I shake a room it's got to to small in a big shaker so we can simulate the enormous acoustic and vibrational loads that parts experience during the rocket take off and that's that's really where things tend to break more than any other place good we're
6:12just seeing a little of videoblog thing of the what's that yes exactly during here right now is set up for it says upcoming of our second stage if you're going to send out to up to Texas for a hot fire what you see here is our electrical cross support equipment a copy of what we actually have called on Kwajalein of the launch that we do that we want one replica here send them out so we will be putting the stage to its paces tomorrow and you just some pepper yeah this is our electromagnetic interference test chamber looks vaguely like a torture chamber but it's it's basically set up so that when we can take our rocket or spacecraft and put
7:04put the section here with with all the antennas and radios and because it was like a dozen radios on the vehicle well either transmitters or receivers of rest kinds and we're gonna make sure that don't interfere with one another and that they've got good we can sort of verify that the signal that's going out it's gonna be well received by the ground and that's where we use this chamber for it's really great so what
7:28we're looking over there that's a quarter section of the Falcon 9 17 foot diameter fairing it's 17 foot diameter obviously and 50 feet long it's capable of taking the largest satellites in the world and it can actually literally fit a city bus in that fairing it's that big because that's that's just a quarter section of it it's made of carbon fiber it's very lightweight and uses the most advanced analytical techniques to optimize the mass so it's actually I believe the lightest lightest weight bearing of its kind as well what we're looking at here is the Dragon spacecraft pressure vessel so it's almost done we just need to do the forward and aft bulkhead it's actually
8:12upside down right now so you can see the main hatch the some of the windows the the actual common berthing mechanism where it berth to the space station is well right there yes ordinarily be the other way around and this is an actual flight fidelity article that's going to go through full qualification testing this areas is dedicated to our dragon spacecraft assembly so you see various tools that's for our heat shield making the composite parts and a heat shield of theirs others besides the side shields and the nose cone that's that's all right that's the engineering test article at fiscally interesting Pathfinder for our heat shield for Dragon which is it's used a
8:56very advanced material called the phenolic impregnated carbon ablator which is the really the best heat shield material you can possibly have and this is our engineering test article of our Dragon spacecraft so it's not flight fidelity with the product we saw earlier with with reefs or the welded piece that's actually five DLT but this was used as an engineering Pathfinder to figure out how we might make dragon and actually it's been very useful on the right there is a it's a space station berthing mechanism ring so that's an actual ring that will make to the space station and there's another one on the dragon itself although the guide vanes
9:31aren't on present give various pieces like windows and brochures and frangible nuts and these are structural bulkheads or structural reinforcing bulkheads that's the little model we use to determine splashdown loading so here we are in East High base we're two very large high base when the East one right now the East Highway is used for Falcon 9 stage construction and it's also temporarily used for storage which is why you see various bits and pieces are behind me this area under the high Bay's useful Falcon 9 tank fabrication so you can see behind me various barrel sections for Falcon 9 that's actually serial number two that completed tank is hero number two a
10:12falcon 9 zero number ones and the test stand in Texas and then serial number three is in bowel sections on the floor and we're getting ready to weld together those rail sections and create out third tank which would actually the first flight tank so the first one was to run tank second or qualification tank and the third one will see flight that's a falcon one second stage both former so that's a classic most forming tool that's used to take two welded cones of typical refractory out of metal like columbium half of the malla way and belching it to a round contour which is the optimized contour for maximizing the efficiency of rocket thrust this cleaner
10:52here is also climate control particularly controlled and it's int it's currently useful propulsion components as well as temporarily it's used to do composite layout so that giant tool you see there is the mandrel that's used to create the composite parts for falcon 9 so it creates the the interstage the dragon trunk section and this the propulsion section skirt anything that's a body diameter through a 12-foot diameter center goal part and that that'll be moved over to the actual
11:24composites area when we have that comparison preparation room down which should be severely soon this area is where we do the other falcon 1 structural assembly so behind me that's that's a falcon 1/2 section of a nose cone that's the tool on which the nose cones are made that's it at avionics or the payload adaptive cone that's another plate of adaptive cone that's a mandrel for the falcon 1 inter stage which is
11:53similar to the Falcon 9 inter stage in fact the Falcon 9 interstates just a scaled up version of the Falcon 1 inter stage this is a barrel section for falcon 1 flight 5 so applied 3 the island in the question hats all ready for launch almost ready for launch flight four is gonna be right behind that will launch F in about three or
12:15four months time and then this is flight five which will launch sometime in the first half of next year we would like customers that are just in that we're expect you to be on that pretty soon and this air is also used for composites fabrication so we've got a big oven there she's used to put big pots at a small oven for smaller parts what we're looking at here is a falcon one upper stage so you can see the the engine and actuators and the all that Plumbing's for the attitude control system will actually hold the pressure and bottles there's a lot more stuff that goes in the back there you can see the tank and the full skirt to the back that holds a
12:49lot of the structure that's for flight four and then the flight five unit is is right there applying it with obviously no much stuff done on it yeah this is a nozzle snack section okay so we offer people at work here yeah get free snacks and drink which is kind of a common thing and if that well but well three unusual in the space world and make people working late sand and then they need a snack is something they should be have one readily available all right well thanks for pulling me on the tour that so that was just basic school and there's actually a lot more other than space like facilities we were a big test site in Texas we've got a test launch pad at Cape Canaveral George
13:31Island in the quadrantal and we're looking for great people of all kinds to join the company so if you're interested please send us resume this area is useful the engine components or the major engine components so you can see there's a nozzle or very small nozzles of various stages of completion and then you can also see the copper of things so the chamber liners we've seated over between that that's a merlin vacuum configuration which has got a more spread-out nozzle section and that's the
14:06sea level configuration which has got a sort of short copper nozzle those are the propellant supply lines for Falcon 9 so they've got a single tank that manifolds out to nine engines and then you've got fill and drain lines so there's a total of 10 sets of 5 inch diameter lines that's a manifold out to the various engines so it's kind of like having like a nine cylinder engine car so think that this is out to bending areas so there's a lot of tubes in a rocket and we have a couple of automated to benders that once you program a particular type of tube could be a very complicated - that looks like a crazy pretzel and this machine can make that exact same tube every time
14:50perfectly alright so here we are in the SpaceX machine shop we have she's about 30 different machines of all sizes and shapes wire EDM machines electric discharge machining we've got blaze knows that there's just an enormous amount of metal sculpting that takes place to create the vehicle you know what a lot of people don't realize is that SpaceX makes about 80 percent of the vehicle by value in-house you know for the engine role metal comes in and out comes an engine and so it's all these machines that's that the medalists take it from its raw form and into the final machine part performed so a part like this will come
15:35in as a forging and and then it'll get turned and mold and cut and eventually end up as an engine chamber liner this is a new machine that just arrived just being tested through its paces before we start machining on it they were actually cutting the grooves on a chamber and drilling the holes that are necessary for cooling these are engine manifolds that connect the nozzle in the chamber these are two spirit rocket parts parts for the stages parts for the engines those are some stumps that's a tube for the main oxygen supply
16:10line to Falcon 9 some more nozzle parts here the nozzle part and also part that's our machine shop actually I mean I've gone through everything there's a lot of detail here in some of its proprietary but gives you a sense for what's capable we actually got a lot of off-site machining that we do as well we have a very high engine production rate here at SpaceX this year this year alone SpaceX
16:36will make more rocket engines than the rest of us production combined and next year we'll but we'll make more rocket engines than any country in the world so that's a lot of rocket engines they don't have to go through and be made very efficiently and made very accurately and that's what all these machines are full what we're looking at here is a Merlin 1c fully returned every cool the engine it's getting ready to ship out to our test site in Texas to to be part of the nine engine firing this is actually the ninth and final engine to be shipped down for that and when we do that firing it's going to be quite spectacular it Falcon 9 is the most
17:15powerful single core vehicle in the American fleet and when Falcon 9 heavy debuts and in about two to three years that will be the most powerful vehicle in the world because the shuttle will have retired by that point so that's really quite significant the Royal equivalent of an Airbus a380 or 747 this
17:35thing is the turbo pump this is this is the chamber nozzle and then there's all a supporting structure in there with the avionics and control valves and here you can see the difference with the Falcon 1 configuration so it's a sealed pyramid the stage valving is contained inside that that that pyramid but other than that is substantially the same of a turbo pump and the chamber and nozzle very little difference really between the Falcon 1 configuration the Falcon 9 configuration you
资源与出处
- 视频在 YouTube 收看
- 档案silicon-valley.tech 档案页本页视频与文稿数据来自 Elon Musk Archive
- 精读本篇精读 Markdown 版