发布会·中文精读

马斯克带逛 Starbase(2021 夏季·下)

Starbase Tour with Elon Musk [PART 2 // Summer 2021]

中文精读由 AI 基于原始视频与文稿改写,非官方翻译,可能存在偏差或错误;表述以原视频为准。说明

我们其实希望早期的星舰炸掉。

这句话是马斯克在星舰基地的组装帐篷里说的,语气很平,像在讲一条生产流程。

逻辑特别朴素:星舰和助推器几乎每一发都有大幅改动,早期那些如果全都完好无损地留下来,你就得找地方存放。马斯克的说法是,它们要么变成漂亮得不得了的草坪装饰品,堆到十几台会很难看,要么干脆炸掉。

所以他宁可在早期把东西推到极限,看它在哪里断。

这是 Everyday Astronaut 的 Tim Dodd 2021 年夏天参观星舰基地的下半场。上半场走的是室外,下半场钻进三个总装帐篷,正好撞上猛禽二号发动机、星舰 S20 的隔热瓦,还有马斯克那套关于「为什么必须失败」的完整论据。

龙飞船、猎鹰九号、星舰,三种完全不同的失败观

马斯克自己把这三条产品线排了个谱。

一头是龙飞船(Dragon)。「龙飞船上不能有任何一次失败,所有东西都要测到六遍,必须有大量余量,任何原因导致的任何一次失败都不允许。」这是极端保守主义。

中间是猎鹰九号(Falcon 9)。「助推器着陆失败了,也不是世界末日。」

另一头是星舰(Starship),「和龙飞船是两极对立」。目标是造出人类第一枚完全可重复使用、并且是快速重复使用的轨道火箭,重复使用的方式要像飞机那样。

这两个词得分开看。可重复使用和快速可重复使用,中间差着一个数量级的工作量。航天飞机做到了前者,没做到后者。马斯克说航天飞机那套流程里,「快速」这个词得划掉,「翻修」才是更准确的说法。

航天飞机真正的病根,是风险收益不对称

为什么航天飞机没能迭代?马斯克的答案很简单:上面有人。

「上面有人,你就不能炸航天飞机,所以完全没法迭代。」

但他接着往下挖了一层,这层更值得琢磨。航天飞机的很多问题是已知的,工程团队不是不知道,是不敢改。因为改了出事,惩罚巨大;改了没出事,奖励很小。这种不对称一旦形成,设计就冻结了。

热防护泡沫脱落砸到机翼前缘,O 型环低温失效,这两个后来酿成大祸的问题,在事故之前都反复出现过。「因为它之前一直没出事,大家就觉得不会出事。」

马斯克的原话是:俄罗斯轮盘赌之前也一直没出事。

星舰上没人。这是它最根本的竞争优势之一。可以炸,可以连续炸,可以把炸出来的数据当成产品。

发射逃逸系统,星舰干脆不装

Tim Dodd 问了一个很多人关心的问题:星舰将来载人,会不会做发射逃逸系统?

马斯克的回答是不做,理由是这东西在物理上撑不到终点。

传统的发射逃逸系统,是在返回舱顶上装一台固体火箭发动机。这台发动机每飞一次都得抛掉,抛不掉乘员就全没了,这本身就是一个新增的失效模式。火箭一点火,系统里就多了一个必须成功一次的状态变化,这在工程上是坏消息。

而且逃逸塔太重,带不到轨道,所以通常在二级点火后不久就抛弃。也就是说,逃逸能力只覆盖上升段的前一小截。

龙飞船现在的方案更强,逃逸能力一路覆盖到入轨。但返回地球这一段,谁都没有逃逸系统。

再往外推,月球和火星上也不可能有。火星大气密度只有地球的百分之一,弹射出去的东西会以超音速撞地,救不了人。

所以结论倒推回来:飞船本身必须安全到不需要逃逸系统的程度,否则月球和火星就去不了。在地球上单独为上升段加一套逃逸装置,反而成了半途而废的设计。

星舰的做法是靠冗余和飞行次数。丢掉一台助推发动机没事,丢掉多台也应该没事,飞船上丢一台同样没事。然后用一百到两百次飞行把所有失效模式摸清楚,把风险压下去。

一吨隔热瓦,实际要付两吨的代价

这段话值得慢慢拆。

Tim 问,隔热瓦如果不够,加厚一点不就行了。马斯克说不行,因为质量是递归的。

你往星舰上加一吨隔热瓦,为了把这一吨送上轨道,需要更多推进剂;为了把它从轨道上带回来,需要更多推进剂;为了带着它着陆,还需要更多推进剂。同时结构本身要承受这额外一吨的载荷,所以结构也得加强,结构一加强又是新的重量。

SpaceX 算下来的递归系数大约是 1.8,马斯克觉得可能算漏了什么,真实值接近 2。

也就是说,往星舰上加一公斤,真实代价接近两公斤。

这条规律解释了星舰上几乎所有的设计取舍。为什么用不锈钢而不是碳纤维?为什么把助推器的着陆腿删掉、改成用塔架接?为什么推进剂加注管线从助推器挪到地面?为什么这一版飞船干脆不做舱门?

每一处都在做同一件事:把质量从天上挪到地上。

零级比助推器还难换

马斯克在访谈里反复提一个说法,第一次听会觉得别扭:发射系统叫「零级」(Stage Zero)。

它包括发射塔、发射底座、导流槽、推进剂储罐区,以及所有的管线。

他说这话的时候特别强调:「对我们来说,造一个零级比造一枚助推器或一艘飞船更难。」

所以第一次轨道发射的首要目标里,有一条是「别在发射台上炸」。

Tim 追问第一次发射的计划。马斯克说,助推器要做返向点火,溅落在墨西哥湾,离岸只有二十来英里;飞船绕地球大约四分之三圈,再入后溅落在夏威夷附近一个军事基地外侧的太平洋上。

「最好的结果是助推器完成任务、还能重新点火,然后精准地溅落在某个位置。如果它当时是停在塔边上,机械哥斯拉的胳膊能不能抓住它?这就是我们要验证的。」

机械哥斯拉(Mechazilla)是那套捕获臂的名字。Tim 问细节,马斯克说捕获点就是两个很小的、像霸王龙前肢一样的支臂,配一根扁平的托臂,那两根小东西能承受很大的载荷。

为什么非要用塔架接,而不是留着陆腿?因为着陆腿本身是死重,而且是在最不该有死重的地方。挪到地面上的塔架,天天都能用,还能反复用。

第一次入轨,目标只是别炸

关于首飞的轨道方案,外界吵了很久:到底是真的入轨再脱轨,还是打一个高椭圆的亚轨道弹道?

马斯克的回答是:速度达到入轨速度,但不圆化轨道。

飞船会绕地球大约四分之三圈,因为近地点没有抬起来,大气阻力会自然把它拽下来,再入速度跟真正从轨道返回差不多,区别不大。

这个设计的巧妙之处在于余量。马斯克说,只要姿态控制推力器喷一下,甚至冷气推进的排气本身,就足以把近地点抬进轨道。抬起来非常容易。

首飞的成功标准被切成了好几层。第一层是别把发射台炸了。第二层是助推器完成自己的活。第三层是飞船入轨。马斯克说得很直白:

「说实话,如果它起飞的时候没把发射台炸掉,那就算赢了。发射台比助推器难换多了。」(马斯克)

他还补了一句,如果助推器干完了活,飞船那边出了问题,他依然认为这是不错的进展。

猛禽一号到猛禽二号,从圣诞树到裸机

帐篷里摆着几台猛禽(Raptor)。Tim 一眼看出区别。

猛禽一代的管线密到看不见发动机本体,Tim 形容像一棵圣诞树。马斯克说以前传感器是每两毫米一个。

猛禽二代的管线迷宫基本消失。马斯克说:「猛禽二号肉眼可见地比一代干净。」

他本来想卖个关子,「我是不是不该把秘密都告诉你」,然后自己接了一句:反正长焦镜头都能拍到,「如果哪个傻子想抄这个设计,抄吧,猛禽二号比这个强太多了。」

几个技术参数值得记下来:

  • 当前膨胀比大约 80,目标 90 左右
  • 比冲(Isp)的理想值是 380 秒,实际预期能做到 377 到 378 秒
  • 所有猛禽的涡轮泵和推力室组件是通用的,只有两个变体:带大喷管的真空版,和不带矢量控制作动器的版本
  • 真空版的喷管延伸段有自己的再生冷却通道,是钢管壁结构
  • 喷管型面做了调整,喉部不变,扩张段的角度按更高的膨胀比重新走过一遍型线

马斯克给猛禽二号的评分是 B+。评分标准很有意思,他说这像体操:先看你选的这套动作难度系数,再看你完成得怎么样。

梅林(Merlin)发动机在燃气发生器循环这个架构里是 A+,但那套架构本身不是 A+。全流量分级燃烧(full-flow staged combustion)是 A+ 架构,而猛禽二号在这个 A+ 架构里只拿到 B+。他预计到猛禽五代能到 A+。

鼻锥不用冲压件,因为冲压机装不下

帐篷里有一节正在成型的鼻锥。Tim 注意到它表面比以前的版本光滑太多。

旧版鼻锥由三排冲压成型的瓦片拼成,接缝多。新版只有两排,而且是旋压成形(stretch forming):拿一整张大钢板,套在一个巨大的芯模上,硬拉出来。

为什么不用冲压?因为尺寸超了。冲压机的极限大约就是旧版那一节的高度,新鼻锥放不进去。要造一台能装下它的专用冲压机,那台机器本身还不存在。

旋压成形能行的前提是形状够简单。马斯克解释了边界条件:这种工艺做不了汽车侧围那种带凹陷的复杂曲面,但做这种高度对称的单曲面完全没问题,因为它只需要单面模具。

这一版星舰没有舱门,也不做轨道加注

Tim 问,鼻锥侧面那个开口是不是在装载荷舱门。马斯克说,舱门的工作已经停了。

原话是:「我们先集中精力入轨,入轨不需要门。」

入轨之后再集中精力把飞船收回来,门的事以后再说。他管这个叫「不必要的复杂度」。

逻辑很干脆:最早回来的那十几艘飞船,大概率不会再飞,或者最多再飞一两次,然后就进库房。给一艘永远不会去送卫星的飞船装舱门,属于白干。

猎鹰九号的早期批次也是这个待遇。马斯克说,现在如果要发一次消耗性任务,他们会挑早期的 Block 5 去,「因为早期的 Block 5 不如后期的 Block 5,准备起来也更麻烦」,干脆让它们退役。

轨道加注也是同样的处理。马斯克说得很明确:去月球需要轨道加注,去火星需要轨道加注,往地球轨道送卫星不需要。所以先把入轨和返回做完,加注的事往后放。

顺便,加注的接口方案也变了。原来的设计是从助推器顶部往上走,现在改成从侧面接,因为「把质量挪到地面那一侧永远更好」。

栅格翼为什么摆成 X 形

助推器上的四片栅格翼没有按 90 度均匀分布,而是两两靠得更近,从侧面看像一个 X 翼战机。

Tim 猜是不是为了简化滚转控制。马斯克的回答更细。

三个轴的控制权限需求完全不对等。滚转需要的权限几乎为零。偏航需求也不算大。真正吃控制力的是俯仰,因为助推器返回时要横过来,等于把一个庞然大物硬按进气流里,它自己不想去那个姿态。

所以栅格翼的控制力要往俯仰轴上偏。两对翼靠得更近,俯仰方向上的贡献就更大。马斯克说,理论上还能靠得更近一些,现在的布局是个折中的猜测。

他还用了一个特别土的比喻:这就是个跷跷板,或者说一把扳手。扳手柄越长,转起来越省力。所以栅格翼离质心越远,需要的力越小;反过来,又短又粗的助推器反而更难转。

质心和压心这两个点,决定了整个返回姿态控制的手感。

至于像新格伦那样靠大面积侧身飞行、用气动阻力减速,马斯克觉得星舰不太走这条路。「这东西再入时基本是以接近终端速度下来的。」而且着陆点要求很精,你不能在最后一刻猛地抬头,那种大质量物体转身太慢。他的比喻是:超级油轮不会像快艇一样乱窜。

隔热瓦是陶瓷,两片碰一下就可能裂

S20 整艘贴满了隔热瓦。Tim 说像龙飞船的鳞片。马斯克承认有几片已经碎了。

这里的核心难题是热胀冷缩的跨度太大。金属壳体在加注低温推进剂时降到低温,点火后被高温燃气加热到远高于常温,再入时又要冷却,然后瓦片自己还会被气动加热。整艘飞船从头到尾都在膨胀和收缩。

瓦片是陶瓷,马斯克的原话是「像咖啡杯那种陶瓷」。两个咖啡杯撞一起通常不是好事。

所以瓦片用机械方式固定,留了一点活动余量,让它们能微动。但即便这样,瓦片之间如果互相撞击产生裂纹,再入时就可能是灾难。

「这艘船到了轨道之后,能不能完整地穿过地球大气层回来,是个巨大的问号。它回来的时候就是一颗流星,烧得通红。隔热盾扛不扛得住,或者盔甲上只要有一条裂缝,就完蛋了。」(马斯克)

首飞如果失败得彻底,怎么定位问题?马斯克的答案是装温度传感器,最好再装内部相机。他中途还自己推翻了一次:其实不用红外相机,普通相机就够。钢材在熔化之前会先烧到白热,你直接就能看见哪一块在发亮。

隔热瓦的产地也提了一句。佛罗里达有专门的热防护瓦工厂,SpaceX 内部叫「烘焙房」(the bakery),规模不小,挨着一家 Ron Jon 冲浪用品店的配送仓。航天飞机当年有 24000 片形状各异的瓦,星舰这里大部分是统一的六边形,只有边缘换成方形。这是巨大的简化。

再入时最可能失效的地方,是襟翼的铰链

Tim 问星舰再入时最可能出问题的地方在哪。马斯克没犹豫:襟翼的铰链,前铰链和后铰链都算。

原因是物理上躲不开的矛盾。铰链得能转,所以不能整块用瓦片包死;不能用瓦片包死,就得有密封;密封面对的是一堆表面温度极高的陶瓷瓦,橡胶用不了,只能上金属密封,还得做迷宫式的曲折路径。

更麻烦的是气动布局。等离子体打在襟翼表面,绕过去之后会沿着箭体侧面爬升,撞上那一段不动的固定翼面,热量在那里堆起来。

解决方案里有一个是马斯克早年提过的:发汗冷却(transpirational cooling)。往铰链缝隙里通高压甲烷,只要压力高于外界气流,就能形成一道气膜隔开等离子体。

他还补了一个反直觉的判断:就算甲烷真的烧起来了,也没多大事。因为空气里只有 21% 是氧气,剩下大部分是氮气,甲烷和空气燃烧的温度远低于等离子体本身的温度,而且那层气流本来就已经和高温等离子体隔开了。

龙飞船的隔热瓦为什么厚得离谱

这段技术含量高,也最容易被跳过。

龙飞船用的是 PICA,酚醛浸渍碳烧蚀材料。马斯克说这玩意儿其实相当可重复使用,「它就像刹车片,余量留得太多,能飞很多次」。

问题是它为什么留这么多余量。

龙飞船的再入剖面很陡,峰值热流高,但总热量不算大。它优化的是另一件事:热量脉冲传到瓦片背面、也就是瓦片粘在碳纤维复合材料夹层结构上的那一层时,会发生什么。

如果热量太高,胶会被熔化,隔热瓦就会掉。瓦片密度很低,掉下来会飘,可能直接把降落伞打坏。

龙飞船的瓦片厚,跟烧蚀量关系不大。真正的原因在热量脉冲:它不能传到背面去熔胶,而那个时刻飞船正挂在降落伞下面。

这解释了一个看起来很怪的事:对龙飞船来说,峰值热流高一点反而更好,总热量低才是关键。

马斯克顺带讲了升阻比。很多人看龙飞船是个软糖形状,觉得它没有升力。其实它有,只是很小,靠质心偏移让这个软糖在气流里微微倾斜,产生一个很小的升力矢量。再靠小推力器转动飞船,就能改变这个升力矢量的方向。

所以落点是个椭圆。纵向精度比横向差,横向靠左右倾斜调,纵向靠一系列 S 形转弯、改变倾斜角度来调。

他还吐槽了一句行业习惯:说升阻比必须带上马赫数。很多人只报一个数,但在马赫 20 的时候,那个数是垃圾。

轨道和太空,是两件天差地别的事

访谈中间马斯克插了一段话,值得单独拎出来。

「上太空其实相对容易,入轨非常难。入轨再回来,比上太空难一百倍,可能还不止。」

他举了布兰森的例子。2005 年前后布兰森两次上太空,飞船的漆都没烧焦。这说明那个速度下的气动加热根本不算什么。

而入轨回来的东西,必须带真正意义上的热防护,否则就是解体。

这段话说得轻描淡写,但它解释了为什么蓝色起源和维珍银河做了这么多年,跟入轨之间还隔着一道鸿沟。亚轨道旅游和轨道运输是两个行业。

时间是这个世界上唯一换不回来的东西

Tim 问,现在最让你睡不着的是什么。

马斯克的回答没有落到具体的技术难点上。他说所有事情都要换算成时间风险来衡量,然后承认了自己的一个特质:

「唯一换不回来的东西是时间。我确实有个习惯,时间表定得过于乐观。但如果我不乐观,我就不会去做这些疯狂的事情。所以我大概是有病一样的乐观。」(马斯克)

这句话放在 2021 年夏天说,回头看有点意思。当时他说助推器下周就能完工,发射环第二天就吊上发射台,「我们可能不会成功,走着瞧」。

他还说了一句给所有人的提醒:这里看到的一切都是进行中的状态,上周说的话下周可能就不成立了,也可能是说错了,也可能是找到了更好的方案。

访谈尾声撞上一个巧合。助推器编号 4,飞船编号 20,助推器高度 69 点几米,因为工程团队嫌 70 米那半截筒段麻烦,直接删了。马斯克说自己当年是随手定的 70 米,没什么特别含义。

然后他补了一句:我出生在 4 月 20 日之后的第 69 天。

Tim 说这太荒唐了。马斯克说,是啊,荒唐。

这套方法论能拿走的部分

整场访谈下来,马斯克讲的其实不是火箭,是一套关于「怎么在资源有限的前提下快速逼近正确答案」的方法。这套东西搬到软件、硬件、内容生产上都能用。

  • 先分清你的项目属于龙飞船还是星舰。有人命在上面、失败不可接受的产品,就用极端保守的流程,测六遍,留大余量。没有人在上面、失败可以承受的产品,就快速迭代,主动把早期的版本推到断裂点。最糟的是拿星舰的心态做龙飞船,或者反过来。
  • 算一遍你的递归系数。任何一个组件的增重、增量、增加复杂度,都会连带拉高结构、能源、散热、运输的成本。SpaceX 算出来接近 2 倍。你的项目里这个系数可能是 1.5,也可能是 5,但你得知道它是多少,否则每次优化都在做无用功。
  • 把质量挪到地面。能放在基础设施上的东西,别放在一次性飞出去的东西上。着陆腿换成塔架,加注管线换成地面侧接口,都是同一个动作。软件里对应的就是:把逻辑放在服务端能改的地方,别烧进客户端。
  • 先砍掉非关键路径上的功能。舱门不做,轨道加注不做,因为入轨和返回还没跑通。判断标准只有一个问题:这个功能是不是解决当前核心问题所必需的。答案是否,就停。
  • 检查你的组织里有没有风险收益不对称。如果改对了奖励很小、改错了惩罚巨大,你的团队一定会像航天飞机项目那样把设计冻结,然后带着已知问题继续飞。这个结构不改,招再多人也没用。
  • 第一版诊断工具越土越好。马斯克一开始说要装红外相机看罐体内部温度,聊到一半自己推翻了:普通相机就行,钢烧到白热会发光。省下来的钱和工期,比多装一个传感器值钱得多。
  • 公开承认你的时间表会跳票。马斯克自己说这是病态乐观,然后照样每次都定得很激进。这套做法的价值落在速度上。预测准不准是次要的,把团队推到极限才是他要的。前提是你得说清楚这是乐观估计,而不是承诺。

最后一条,技术上不算建议。Tim 问,很多人想开始做视频但不知道从哪开始。马斯克说,你就是得开始,逼自己开始,然后从那里改进。

星舰的隔热瓦现在还有裂纹。猛禽二号只拿到 B+。第一次入轨的目标是「别在发射台上炸」。

他们照样往下走。

YouTube 平台字幕(自动或人工),可能有识别错误,人名与数字请以视频为准。已按语句合并成段落,并去掉 um、uh 等口头填充词。 文稿来源:YouTube(自动/人工字幕)。

0:00hi it's me Tim DOD the everyday astronaut welcome to part two of my tour of spacex's Starbase Factory with the ultimate tour guide Elon Musk if you haven't watched part one you obviously need to watch that because there's just gobs of information and in this part we're actually going to go inside the three main assembly tents which is incredible and just like last time we have a map that will occasionally pop up courtesy of ring Watchers on Twitter that'll help you understand where exactly we are in the factory we also have the YouTube play bar broken up into certain sections we have links to those sections below too and we have an article up on our website that has some

0:36key points and takeaways of this conversation the link in the description is below for that at everyday as.com all right let's go check out some Raptor engines so by the way I think there's a good chance that that itar and comms might not want all just like you know it just can't be any any more than people are already getting from True telephoto lenses that's which is pretty much and frankly if some fool wants to copy this design go for it I mean Rapter 2 is a giant improvement over this so what's like the big simplifications you're hoping to have well maybe I shouldn't tell you all the secrets we have like funny things on the good Pikachu over there I love that hello

1:26again hello again so that probably I assume that means it's flown is that a flown one I don't know if this one's been flown jeez this really does look like that that thing with all the NK 33s you know those videos ex like the engines discovered engines that came back from the cold yes and seriously literally looks like that this is insane and the man that rrap is

1:51big jeez I want to tell you all secrets but just like you'll be able to see the difference very clearly okay and I guess since the engines are it's hard to have people not see them yeah they will you will it's it's the Raptor 2 is visibly cleaner than Raptor 1 like it's this this sort of maze of plumbing and wiring doesn't exist on raap 2 although it's already slimmed down a ton from like you know the it used to look like a freaking Christmas tree yeah U like you couldn't even see the engine P the stuff that no you really couldn't and now it's like especially around the turbines and stuff and the pre-burners it's I mean that used to be a whole there's sensors

2:31every every two millimeters yes so wrap V or Raptor back has its own regen channel on the extension it looks like yeah that's a steel tube wall ra steel tube wall that looks and it has a different profile too that actually looks like the the initial exit is there a different throat in it and everything or is it throat's the same throat the same it's just the part after the throat that's the diverging section has different angle it's basically following a route contour for a higher expansion ratio yeah yeah what is expansion ratio again is it like 150 or something no man I think we're so so this is actually there's I think we're around 80ish oh okay but we want to get to

3:24we want to do a little bit better maybe 90 so cuz you're already getting like 380 ISP out of that thing aren't you I mean sorry yeah 380 380 is the aspir aspirational number okay but we should be I think we think we'll get like 377 or 378 okay so okay and how are those coming along looks like obviously you've got a third one here you've obviously made at least three yeah and I obviously or s20 is going to have three yes yes so jeez but the for Raptor all

4:06engines will have the same pumps and thrust chamber assembly so it's really just they'll be one sort of one one variant that has a big nozzle and one variant that doesn't have thrust vector control actuators okay okay so that's and that's going to be the difference between the the r boost and the yeah I mean it's basically the same engine minus TVC gotcha so the outer shells that you're working on for the gsse are 12 12 M there's a raptor without the stuff looks practically naked you're like actually that's secretly version two it's super simple no version two will look a bit like that actually it's very tight really I mean again kind of when you look at some of

4:53those Soviet engines they were also like incredibly simple looking I'm guessing they just obviously didn't have them wired to the gills with with electronics though either you know they did they simply did in back in those days they they did not have good Electronics so there's nothing to there's nothing to wire yeah is how much like I feel like

5:11you you iterate this quite a bit and and remind people that it's failure kind of is an option why do you think people are so afraid to fail and why do you embrace it or how do you how do you teach that culture even that it's okay when you're not even trying to like you know sn8 is a perfect example you weren't trying to like do a mission you're just trying to get data out of the thing yeah we have just a fundamentally different optimization for Starship versus say like the the polar extreme would be Dragon like Dragon there can be no failures ever everything's got to be tested to you know six ways to Sunday

5:50there has to be tons of margin they can never be a failure any ever for any reason whatsoever y so they cannot be we can't be so that's like extreme conservatism mhm then Falcon is little less conservative it is possible for us to have say a failure of the booster on Landing that's not the end of the world right for and then for Starships is like like the polar opposite of of of dragon we're iterating rapidly in order to create the first ever fully reusable

6:25rocket orbital rocket mhm and fully fully rapidly reusable reusable in a in a way that is like an aircraft mhm so rapidly reusable Rockets it's a big deal yeah that's the that's the fundamental Poly Grail for making life multiplanetary where do you think the space shuttle failed in being in any definitely rapidly would be a word you got to scratch off the list and refurbish might be a better word but where do you think it failed do you think like what lessons have you learned that that you know you're not going to be making on Starship space shuttle had almost no room for iteration because there were people on board so you could be blowing up shuttles yeah so that's a big problem

7:13y well they did very very little it I mean yeah like very little in fact lack of iteration was a problem because they a lot of the issues they were aware of but people were too afraid to make change because the design froze yeah cuz it's it's like yeah I mean there was a risk reward

7:37asymmetry mhm so big punishment for if you make a change and something goes wrong big punishment if you make a change and it goes right small reward yep y so the issues with the O-ring and and then with the insulation coming off and hitting the the wing yeah we they've seen this before yeah they were known they they known issues yeah so which but it it because it had worked before they're like well it worked before Russian Roulette Works

8:14before right so look I've pulled the pr out so many times must be no must problem yeah so anyway it's just you it's hard to iterate though when people are on every Mission so you can't just be blown stuff up cuz you're going to kill people Starship does not have anyone on board so we can blow things up yep that's really helpful do you have any considerations yet on on any kind of launch Escape or you just hoping that by the time you put people on it you've flown it say 100 to 200 times and you're familiar with all the failure modes you've mitigated it to a high degree of of confidence or what's your yeah launch Escape I think is yeah you basically

8:54just need to fly a lot and have a lot of redundancy so if you lose an engine on the booster it doesn't matter basically if you lose multiple engines it shouldn't matter and you should be able to lose an engine on the ship everything's okay so because launch Escape is basically just protecting you for the asent phase and actually most launch Escape systems only protect you for a small part of the asent phase like cuz the typical launcher system is a solid rocket motor on the tip of the capsule yep which then has to be has to be

9:37jet it has to be jettison on every Mission so if it's not jettison the crew dies that's a failure mode right there that's a failure mode so you have a state change post LIF off which is bad then because the D thing's so heavy they also can't carry it all the way to orbit so they'll typically jettison the the Escape system shortly after second stage ignition y or fin final stage ignition yeah so so then you don't have Escape all the way to orbit even now at least with dragon we we we have Escape all the way to orbit so that's like I think safety Improvement yeah but but then you you know there's no Escape system coming back to earth like that doesn't exist

10:17right and then there you can't have an escape system on the moon or on mars or on Mars yeah so like you you can't have something pop off and then have shoots drop there's no atmosphere right and then Ms has a very low density atmosphere so they'll just like hit the ground supersonic you know right not going to save you so ship has to be safe enough for people without an escape system because otherwise you can't go to the Moon can't go to Mars right right so kind of pointless to do it on on Earth well it just fed a lot right and that I mean I never really thought about that that you know you're going to be you know you're going to be flying so much

10:56without fear of Retribution of failure that unlike shuttle like you mentioned I just never really considered that you know yeah so let's see what what is Oh that's oh those are the the vacuum mounts aren't they yeah wow that's cool yeah I mean this is L stuff like very much Vision one so

11:27yep it could be it it'll be a lot better with the next iteration well a lot of people ask me and know like hey I want to start a YouTube video where do I start and I'll be like start you just have to start and I kind of feel like this is that a similar philosophy it's like you're not going to know what's wrong or how to make it better until you do it at least once anyway you know and you just simply have to start you have to force yourself to start yeah and then yeah that's that

11:56you improve from there exactly man are you pretty used to the heat I feel like it's it's it's pretty hot out here it is hot I mean this is the worst this is like summer you know so right that's just like the worst of it yeah it's not that bad if you think like just pretend you're in Hawaii right there you go so speaking of of shuttle I mean I think it's a cool view oh it's a really cool View and thermal protection it seems like you guys have made some I it looks like s s20 is going to be pretty well decked out in the stuff how you feeling about the thermal protection system you feel like that's a pretty good solution we'll find out have they been holding up pretty

12:50good at least on the on the low altitude stuff as far as the mounting points and stuff like that it hasn't puled I mean it's still there I mean you can see the videos yeah it takes off with the tiles and it lands with the tiles y and we have I think a good attach mechanism which it seems like a good attach mechanism cuz it allows it's just mechanically attached with some play in the tile so the tile can move a little bit like it's quite a tricky thing with the tiles cuz the tiles are essentially a ceramic right and and there's a they're attached to a metal substructure that is changing in temperature dramatically so it'll be you know room temperature right now

13:40then it'll drop to cryo temperature when it's loaded with cry Jen propellant then it will be heated up with hot olish gas so now it'll be way above room temperature then it'll cool down then the tiles will themselves will get hot on re-entry and they also have some expansion yeah so there's a lot of expanding and Contracting going on all over the place so I think one of the big questions is are these tiles are we going to have a crack or a gap in the tiles like if they Bang into each other the Ceramics like a coffee cup ceramic so you bang two coffee cups together it's usually bad it's not good yeah so if if we if the if the tiles bang bang each

14:28other and and crack this could be this could result in a failure on Entry so I think there like a huge question of like when we get the ship to orbit how is it able to make it back through Earth atmosphere cuz it's coming like a meteor you know it's like blazing hot meteor and will the heat shield stand up to it or if there's if there's any crack in the armor it's going to it's toast yeah yeah so hopefully we at least find find out where the crack in the armor is that would be great and then if you have to you can make something thicker or small or iterate to that degree of where you find those failures again yes how

15:11will you know like what if what if something just goes what if you know the first orbital attempt just goes totally you know doesn't even make it in for re-entering it's just a million pieces at the bottom of the ocean how will you know where it failed I mean we have temperature sensors

15:37probably probably need like some thermal images inside the tanks so just like IR cameras you can see if certain spection is getting real hot yeah I cameras on the inside will show you what the backside temperature is yeah yeah I'll let you know if a Le something pop if the backside temp like it was frankly I'm not sure I take it back if you just have a camera camera yeah you'll know tool yeah you will see is something glowing white hot okay that's bad that's the bad part right there so you don't even need a theral engine frankly yeah the steel will glow white hot before it melts right right right so you'll know you'll know it's so subtle

16:19and the very first orbital test again it kind of seems like you are you guys there's been a lot of debate of like is it going to orbit and deorbiting or is it just orbital velocity with a low parag that's inside the atmosphere and that's how it deorbit like will it no it's it's it's getting to orbital velocity but with a with a but it's it's not circularizing its Pary yes so it it basically goes like 3/4 of the way around the Earth but because we didn't raise the Pary the atmospheric drag will pull it in yep and the velocity will probably be greater re-entry velocity will be greater that way or similar similar yeah it's not it's not a huge difference but it's

17:03it's it basically like it could easily like if you just puff like the attitude control thrusters or like the ol gas ol gas alone could put put it into orbit so like raising Pary slightly is is easy it's like remarkably easy so you just want to raise it like a little bit are you hoping to actually recover the first one or like try to even land or any I mean is it going to first one is first for the first orbital launch I go is to make it to orbit without blowing up that's our goal yep and frankly if we even get the if the booster even does its job and something goes wrong with the ship I would still count that as good progress yeah like basically

17:44actually to tell you Frank if it takes off without blowing up the blowing up the stand stage zero which is much harder to replace than the booster that would be a victory please do not blow up on the stand that's what I want concern but you keep calling if you you calling the stand stage zero the launch system really

18:03yeah the the the ground G the tower and all that stuff St zero yeah okay yeah that's I I just get I got so spoiled now with again Soviet nclat it's like there's zero for like the boosters of soy and core is one okay and then what I would call the wait one no sorry opposite the boosters are one core is two but what what like the next upper stage or what I would consider stage two is stage three so it's really confusing and I kept being like Oh yeah third you know second stage and like no no no that's third stage you know so stage zero the launch system yeah the

18:38launch Mount the flame diverter sort of Y sort of the big tower yeah the propellant Farm and all that basically you know all the liines and everything it's that's stage zero and it's very hard yeah it's harder for us to make a stage zero than to make a a booster or ship okay so hope hopefully it doesn't blow yes that would be great and then like the the best case outcome for the first flight would be that the the booster does its job and

19:17also is able to relight the engines and it's going to splash down yep in the Gulf only like 20 mil out or something right yeah not far Rel and then the the the ship or upper stage is going to come in just off the coast of Hawaii near a military base there and so we'll you know splash down in the Pacific mhm yep yep so so so again to

19:46reiterate on the first launch you won't the booster you're going to just use the gas venting to orient it for re-entry is it will it won't even do a you will do a boost back burn though on the first one too right let's just say it's an evolving situation yeah in order to be 20 mi away we definitely would have to do some kind of boost back otherwise it's going to be way further y so yeah I mean probably it's a boost back and then a propuls and then basically you want to simulate the The Landing but not not not have it be too close to land so it doesn't take out stage zero right y yeah so we want to say like basically can we can position the the booster precisely y such that if

20:32it had landed next to the Tower or if if it had come to a halt next to the tower could the arms have grabbed it yes mechazilla yeah mechazilla me mechazilla megazilla Mecca mechazilla okay yeah like a giant mechazilla yeah and how what's what's the plan is it just come in and it sits then on the on the grid fins Andor that little arrestor thing those those little the little tiny arms that tiny little T-Rex arm is going to hold the yes there's two of them but those those things can take a lot of load and then it's just literally like a flat like a flat arm kind of like this that I mean this is one of those things like it's hard to keep a secret

21:10when it's right there people can just take zoomed up put like drive past it and take a high-res photo close up so it's not exactly going to be top secret right right this is the first real big rocket development that's been so close to a public road that people are literally driving to the beach right past the launch site well so it's hard to keep a secret around here that brings up I always keep wondering like you know we're seeing this insane Pace we're seeing all these crazy things happen how much of that like is normal at least as far as SpaceX goes or how much is that is just because we're actually seeing it like for instance when you're developing Merlin

21:44and and Falcon 9 were you blowing stuff up this much doing things so crazy fastpac or is this like also fastpaced but now we're also seeing it all so it's hard to compare well I mean this is definitely a case where we are washing our laundry in public yeah yeah and there are there's always dirty laundry in any program it's really a question of whether it is seen or not not is there dirty laundry right right yeah every program's got dirty laundry but in this case it's it's it's in public but this is also a case where it's in we're intentionally iterating the design rapidly y and basically ships and boosters will either be amazing lawn ornaments

22:28which they have to be stored and they look awesome but you know we don't want 12 of them it's going to look bizarre and we where we put them yeah so we since we're making rapid iterations with each almost with basically every single ship and boosters had significant iterations but you you either you either wanted to blow up or the the early ones you want them to blow up or you going to have to find a place to store them right so we actually want to push the envelope and and and frankly like if you don't push the envelope you cannot achieve the goal of a fully and rapidly reusable rocket yeah it's not possible yeah you have to go close to the edge

23:14on margins right and there's a recursive factor to mass so like if you add say an extra ton of heat shielding now you also need more propellant to get it to orbit you need more propellant to deorbit it and you need more propellant to land it yes and the structure now has more load so it's because it's carrying that extra ton of heat shield yes so this this applies to Any Given ton there's a recursive value yeah so in order to achieve the same payload you you have to each ton is like basically almost

23:52like adding two tons when it's fully considered definitely so I think we calculated it to be like a 1.8 Rec Factor but I think it's probably wor forgetting something as so it's close to or two yeah so every one ton of mass forgets an extra ton yeah so so what's for instance like what's s20s dry Mass kind of looking like where what are you at right now are you like 120 tons or you I actually don't know the exact mass of 20 we we'll know it when we wait yeah [Applause] there's a lot of parts that have not been weighed so so like what is it actually I mean I hope it's not too insane ideally it's it's dry it's dry

24:47mass is hopefully not much more than 100 tons really so yes but then you say like Dy do you mean not counting the air inside it right by the way the a actually air mass is non-trivial no it's not this is a giant volume and then do you mean dry do you mean with prop residuals and ol gas which is at several atmospheres which Mass are you referring to like sometimes in these things they'll play games with like the when you say thrust weight of a rocket engine so thrust weight of the rocket engine with or without residuals that's a big yeah change or with or without gimbal is something else that I've heard people kind of debate yeah yeah mland is I'm

25:29pretty sure by any standard the the the you know I think it's probably the best thrust to weight of any engine yeah because it's like just so far we we really push the GG cycle engine to the it's like a A+ for GG cycle architecture the GG cycle architecture is not an A+ architecture arure right full Flow gas full flow stage combustion A+ architecture but with a new architecture we won't get an A+ within that like it's like in gymnastics you know you like say how hard is your program right and then what grade you get in the program that's kind of how the you know things work here so what

26:05what would you say version 2 is going to kind of come in at if you were to rate I don't know I'd say it's like B+ okay something like that so good enough for now but of course yeah Raptor 3 raptor 4 Raptor 5 yeah you know by Raptor 5 it'll be an A+ yeah so yeah should we walk through here and check out what's going on in here is this is it this is just a nose being assembled it's not it's not that it's showing it's this is this is our new and improved no cone oh oh yeah it's just straight there's no crosssection so this is if you look at that nose cone over there that's made from stamped sections yeah so you can see that's like three rows of stamped sections yep this is this

26:52is this will be made of two rows of stretch formed wow so and you can see it's like it's just way smoother yeah this is just stretched over a man like a big mandrel so just take it just take a big sheet of Steel wow and you just stretch it over this giant tool right right right so and then you can you can have like things that are way bigger like you can't fit this in a stamping press right this is way too big that's like the basically about as long as you can fit in a stamping press you canot fit something this giant in well you could technically make some totally special case stamping machine that doesn't exist right but you only need one since you only need a single-sided

27:30it's it doesn't have like indentations or anything so like you couldn't make up a a car body side this way but you can make something with this level of symmetry that that is it basically you can do a one-sided die okay so you just stretch for it over big Mandel and this isn't the cargo is not show it's just not complete yet but it had that opening on the one side that that's not because you're working on the door the Jaws yet right yeah I I actually stopped work on the on the door the fairing door okay yeah we're going to focus on getting to of it y we don't need a door yep yep so it's like do we just need we need to be super focused on getting to of it then Super focused on

28:11getting the ship back and then we can worry about doors okay it's just unnecessary complexity see like is the door necessary to solve the problem no will we use this the the like the first 10 or more that that get back from from Orit we won't we probably won't fly them again right or or maybe once or twice but then they're going to be in storage like for Falcon 9 and even like the block five So-Cal block five which is more like version seven yeah really but we don't even want to use the early block fives so like even those are a pain in the ass and we would prefer to retire them so like when we have like a mission that requires an Expendable booster we'll put an early

28:55block five because the early block FES are not as good as the later block fives wow and they're more of a pain in the ass to get ready for flight wow so so the reality is the early ones are going to be amazing Lan ornaments yeah I mean as good as Lan ornament gets but they will not be nearly as good as the ones that follow so then why keep them flying they're not even going to be doing any you know they're not going to be putting any payload up you know they're not you don't even need we going to retire the ear once anyway so yeah why have a door on a thing that's never going to fly satellites anyway yeah how how is the the butt to butt refueling going is

29:38that cuz that's got to be a pretty early consideration cuz you're probably going to want to start testing that no that's we no we're going to get to over and back first okay we don't need we don't need orbital refilling unless you want to go to going to the Moon you need orbital refilling going tomorrows you need orbital refilling delivering satellites to Earth orbit you do not need orbit refilling right right so let's PT that to later okay I'm not sure it'll be the butt but it might be some might like the we're actually we switched the propellant full full drain lines to be side so coming from the side not up through the booster anymore cuz this it

30:19was adding a bunch of stuff to the booster and then we flying it every time so it's better if you can move Mass to the ground side it's better to move Mass to the ground side that's s took the legs off the booster and have just have the the tower catch it are you are you thinking about doing a a tower catch which sounds mad I mean yeah I know I know it sounds insane but when I like suggested that people thought I was L my mind which I'm like maybe I have but I think it'll it'll it might take a few kicks if the can but we'll get it right yeah and then it just the the work that you have to do to pick up the booster and put it on the launch stand gigantic skyscraper

30:59thing in high wind you know like windy situations it's not it's very windy around here yeah it is so you going to pick up the booster you got to put it into onto it stand with Precision then you got to pick a ship up and put it up on top of that so you that means you got to have a secondary arm to steady the the booster so it's not moving around all over the place and then while the sort of meaz alls pick up the ship and put it on the the booster okay so that the the maxzilla arms are the ones that are going to be picking up the ship not the crane okay

31:39so it's very important to appreciate that everything you see here is a work in progress what is said last week may be untrue next week we've seen that a few times yes it could be that we're actually just literally mistaken a miscommunication any any one of number things we just found a better had a better idea in the case of like for the first stacking we're going to do that with a crane yeah we will so

32:11yeah M the Martian right there I love that so the first one we're going to stack with the crane cuz otherwise we'd have to wait for the the all the mechanisms to work so we like we're like assembling the arms and you know basically putting mechazilla together but in the meantime we could be launching right so let's not wait for the tower to be completed we've got like the second biggest crane on Earth let's like it's like we don't necessarily want to have the second biggest crane or it's just sitting there forever but it can be there for the first stacking and then from the first stacking then we can figure out you know just like do we have the

32:57hold Downs the hold Downs work you know like all the launch mounts I should say yeah so it's really quite a complicated launch Mount it's got It's got like basically 20 Mount points right and you got to line those things up and then put the booster on it and have the you know does it fit mhm okay it doesn't it won't fit basically now we're got to adjust it okay that that that launch ring is 370 tons so and it's to tweak

33:28like you move it from one place to another it tweaks yeah you know it doesn't stay exactly the same so we're going to have to like jiggle it around a little bit put in some shims and stuff and fit fit the booster so we want to do that soon we should be done with this booster I don't know next week y so wow so then we want to mount the booster next week it's going to be that's going to be insane to see yeah 're we're going to try to put the ring on the the stand the launch ring on the stand tomorrow wow but we

34:12may not succeed we'll see so probably the second flight will use I mean it's very like the second flight will use the tower okay second flight we use oh so the first flight might still just use the subal pad no it's going to use the it's going to use it has to use the overal pad we can't we can't theal the subal pad cannot take the the full weight of the stack it's going to get crushed and it doesn't have enough height so the rock would blast itself in the face is too low and too weak yeah okay so we got to launch it from

34:49the the super beefy stand yep but we don't want to wait until everything's ready with the tower just to stack okay so how will you secure it then when it's stacked like just drop the start on top the crane holders until it's launch time and then no we we do need the the QD arm to work yeah oh right so that can be a stability thing yeah exactly it holds it it it stabilizes it and transf propellant if we don't have that we can't load prop in the second on the ship okay so that has to be complete but not necessarily the arms and everything else going on at that point yeah

35:31so at this point at this point what I mean we're like I said it's there's a lot of moving pieces here so some of this could be ready in time it's possible that the tower could be ready in time in which case we'll use the tower but if the tower is not ready in time we'll use the crane okay yeah so at at this point in development what things are like what things are are you being kept up by at night like what's the thing you're like oh we just need to you know do this or this better or we really I I can't sleep because I'm not we're not we haven't figured this out

36:15yet I'm sorry yeah so what like what things are just totally keeping you up at night at this point what's the thing what's the thing that you feel like you still have to solve at this point I mean it's a long list so what's at the top of that right now for you at least personally [Applause] well this is really all just measured as as in in terms of time like what is the time risk associated with something right the one thing you cannot replace is time so and I do have a habit of being optimistic with schedules I if I wasn't optimistic I wouldn't be doing you know the crazy things that I'm doing right so I must have like I don't know just pathologically optimistic I

37:07suppose wow that actually look at that that's yeah it looks like dragon scales that is incredible do that look cool it's actually like coming together a lot clean looks like dragon dragon scales it really does yeah and it's it's so much tidier and cleaner looking than I thought yeah I mean there's a few breaken tiles but overall it looks cool that's incredible wow so I guess the joints is one of those things that the community has always wanted to know about you know I guess the good thing is the the flaps will for mostly take most of the Wind from this area that you see so I guess you don't really have to cool the inside of the like the flap joint itself cuz

37:46it's kind of already no actually unfortunately we do I think we've have a significant I think again take a lot of what I'm saying with a grain of salt because I often I'm wrong so so sometimes I will say something that is wrong but I'll you know the I I think we have a design error with the with the the non-moving portion of the Ford flaps okay because the the reason we have the the the flaps and the static Arrow the basically the unmoving portion of the plats flaps are there to do do two things to balance the rebalance the ship so it doesn't come in engines first cuz that's otherwise the what the center of mass is quite low yeah and it will come in engines first and burn up

38:43the engines yep so so first you have to rebalance it so that in a Hypersonic regime you're doing like roughly sort of like 60 to 70° angle of attack y because you have a your flying a trajectory that minimizes Peak heat but but you don't care about total heat load you just care about minimizing your Peak heat because you have a a good insulator here not and you're not o blading yes exactly so if you have an ablade of heat shield like Dragon yeah technically that dragon is like fairly reusable actually cuz it's sort of like a brake pad you you could fly it many times yeah cuz it's got so much margin yeah but AA is is literally means phenolic impregnated C later yep

39:28so that's the dragon heat shield so dragon's like hey let's have a give me a a high peak heating but don't make my total heat load High because what dragon is trying to optimize for is what is the heat pulse when it's under parachutes and it's been the the so the the the heat pulse moves through the tile and then reaches the back to where it's bonded to the carbon fiber composite sandwich structure and if the if the heat pulse is too if the heat is too high it will melt the glue and the heat Shi tiles will start falling off and then they will potentially you know just damage the parachute really yeah you start having like these things like right flying off potentially cuz

40:13they're low density so they they're pretty and and like it's like admittedly it's kind of a corner case but that's it that's like the that's like drin heat shield tiles are way over thick because not because of how much of the heat shield will will be bladed but because of the heat pulse that will reach the back of the heat shield that might melt the glue while it's under parachutes wow so yeah interesting

40:40constraint at the end of it all you know like yeah so if you just have a lot of heat suddenly that that's actually better for Dragon like high high peak low total heating yep yep and so re-entry profile is totally different too it can come in steeper as oppos to come in Dragon was come in like just real Steep and it's like the the lift over drag ratio is low for Dragon I mean a lot of people look at it and say it doesn't have any lift but it does if if you have a gumdrop shaped thing and you have offset Center of mass then you can control it because it has a small lift Vector because the Gumdrop is like tilting into the wind slightly it's quite low and actually

41:18L is a function of mock number people most people like qu an L Lev number but like okay what Mark is that and and it's usually like some sort of reference Mark number but like your LOD is complete trash at like Mark 20 it's garbage nothing basically so it's so it's like LOD at what Mark number anyway so it's it's it's got a very low Lev but it does have a lift vector and then because it is symmetric more or less symmetric with little thrusters you can rotate the capsule as it's coming in and change that lift Vector yeah and then so then you and you you and you have a landing ellipsoid because your accuracy longitudinally

41:59is less than your accuracy left or right cuz you so you're changing left Vector said well how do you change the the point where you land if you can turn left or right but how do you change this point is you you do a series of s turns so you S turn and depending upon how much you Bank during the S turns that affects your Long tunal Point and then your lateral Point is pretty easy to tune cuz you just you have a leftt factory going up and right it's not so much people might think like oh you're going up and down that really doesn't work in the grand scheme of orbital velocities and everything it's really about just your actual velocity and where you end up arresting your

42:32velocity is where you're going to drop to the ground pretty much more or less yeah I mean it I think it's just very important for people to appreciate that there's a very gigantic difference between orbit and and space right it is it is actually relatively easy to get to space but it is very hard to get to orbit right and then you say you want to go to orbit and come back yeah this is easily 100 times harder than getting to space maybe a th so much harder

43:04that hardly anyone's even like you know only a few countries have been able to do it right so you know whereas BR ran went to space twice like like 12 years ago I don't know while 15 years ago 2005 yeah yeah it like 15 years ago yeah he went to the Border space twice yep and and didn't even need they didn't even Scorch the paint right so that's like

43:32it's it's really not very hot if you didn't even burn the paint right that's true yeah that's true whereas this needs like really intense heat shielding or it's going to get to you know blow up basically yeah yeah it's crazy to see now honestly so is there some considerations to make the fix can we go out this way or is it yeah I mean just don't let anything in your head all right deal so there's another Barrel section of s20 I mean it looks a little garage shop to be frank but it's it's like weirdly like super advanced technology with garage up well it is very unique of you guys to basically build the Rockets first and then start building a factory around it

44:22you know because the the production system is the actual hot thing right the rocket is is relatively easy compared to the factory and and these these tiles are actually made in Florida at our at a a SpaceX Factory which called the bakery and and in Florida it's next to run John's literally what's what's the future for Florida with Starship are you going to get it flying 100% get it all figured out basically at least get like orbital version ready and then start setting up shop in Florida and do like yeah I think we want to kind of iron out the major issues here and then we'll suddenly be launching Starship from the cape U we might do more at the cape but we'll

45:09certainly be launching Starship from the cape and and like I said we we make the heat shield tiles which is actually quite a big Factory to make these heat shield tiles not a small Factory so next to Rons I didn't well technically is next to Ron's distribution warehouse okay okay literally I was like is that a surf shop oh it's yeah or maybe it's like a factory I don't know but it's got a Ron John's logo cool but the the factory the the SpaceX heat shield tile Factory is quite big it's not tiny cuz it's a lot of you need to make a lot of these tiles and for the most part I'm surprised at the taper it it looks like they're all still uniform tiles which

45:51obviously is a huge Improvement compared to the shuttle instead of having 24,000 unique tiles as you can see we're figuring out but I'm surprised though even as the as the area tapers it's not I would thought man I would wear Mar Mar's head of heat shield engineering it's like I want to text him like yo man what's going on it doesn't seem like there's a ton of unique they mostly look uniform which obviously will help with yeah they're not old uniform but a lot more in the shuttle you what what's your expected what are you hoping to get for reuse out of these [Music]

46:36things oh I mean no meaningful limit H as many as you want [Music] [Applause]

47:18[Music] there we go we got right back into camera setion for you there for a second camera inside a camera

47:36yeah there there there are different shaped tiles you can see some of them at the border there are square instead of hexagons yep so and then because the static arrow is it it's it's still seeing actually a lot of heat the the Bic the plasma is hitting this it's hitting the surface and then it's moving around it's got to somehow get past it so the get super heat plasma hitting hitting that thing then riding up the side of the the vehicle hitting that static Arrow so you actually have a heat concentration there and then you got a hinge that's you have to protect the hinge this is if you said like okay what's highest probability of failure on re-entry is probably the hinge of the

48:24the flaps okay so the the rear hinge and the and the the forward hinge of the flaps because you have to have a rotating thing yes but you can't just make everything out of tiles so you have to have a seal so you have to have a seal against against the tiles the tiles are ceramic like a seal against Dent plates that are super hot yeah so you can't use rubber right so it's going to be a metal seal and with a torturous path what have you thought about back in the day you talked about transpirational cooling yes so that's one of the things you could throw it at is transpiration cool The Joint that would be so cool I just want to see it bleeding methane honestly and just it

49:02will definitely help cuz you can kind of purge that joint with a higher higher pressure gas you know if as long as it's higher than the Ambient Air Stream or the plasma stream it will create a a thermal barrier it's it's definitely one of the things if you really want to nail the the heating on the hinge is bleed fuel gas into the thing cuz

49:32actually even the burning methane is like like with air because air is only like you know what 21% oxygen air is like you say what you ask people what are you breathing like they think they're breathing oxygen you you're breathing nitrogen with some oxygen a little argon and and some argon and Trace gases so but essentially methane with

49:57air which is mostly not oxygen doesn't get that hot so even if it Burnes it's not that big of a deal right right cuz it's already detached from the SM hot as the plasma that's hitting it right so yeah wow all right well let's see I guess the car is the car is okay

50:28so each tent is kind of a designated one's like Barrel section one's nose cones and one's like one's just kind of the thrust pucks and stuff or yeah like I said it's it is a a constantly evolving thing so right we've Mo we've changed what occurs in each production tent and in the high Bay and medbay multiple times but this certainly currently is focused on the nose well you're working you're working on a new highway too right yeah we building a a higher Highway Uber High it's about like it's only a little bit higher than the current one but it's much wider and it has two Gantry cranes that run full width and depth okay so I

51:21mean it'll feel like the lap luxury compared to our current High Bay like how about how tall do you know sorry about how tall I don't know probably oh it's like 100 m okay and this one's so one's like 80 or something yeah this one's about 80 so it's they got the boo booster Heights about 70 although that was kind of funny like technically we deleted half a barrel section from the booster so it's technically 69 something like 69 and 12

51:55he did that on purpose this no it wasn't even me I was like the guy's like hey we we we just let me know we we we took a half the at 70 M you have a half barrel which is a pain in the ass so they just deleted it and I was like cool that sounds good we don't I mean I randomly set the length at 70 M it's not like anything special about it right so I fate loves I don't know I don't know what's going on but these certain numbers just seem to be recurring all the time yes and so the booster is actually 69 point something and then it's booster 4 and ship 20 20 and this is all happen stance right right I love that what the hell is going on so well what oh yeah someone had

52:43figured out that oh what was it it was like oh I don't even remember what it was something like you were 69,420 like days old or minutes old or something when you went on SNL or something like it was like what some we something ridiculous yes it was like the weirdest no I was born 69 days after 420 by the way yeah come on come on it's just ridiculous it's ridiculous that's so funny I mean what the [Music] hell oh man this is insane it's like am I an avatar in someone's video game yes oh really statistically yeah okay you're probably doing pretty good at the game though I bet you're like the top ranked player okay well that's

53:34something so what's do you have a name for the high Bay Bar yet no I guess we've bounced around different names we we still haven't really made much use of it because it wasn't really critical path so it's kind of just sat there and the elevator we need an upgraded elevator cuz we have like it's construction elevator we not yet have a name nor have we used it but we're making good progress there in stalling the yeah GD fin yeah looks like the grid Fin's up and I like how they're now at is there do they just are you I guess I let me let me try and guess why you're going to put them closer together and not at 90° intervals is it because you can

54:18just roll change your roll to change whatever access you're trying to if you're trying to pitch the vehicle you really only most of the time probably either doing pitch or you you're likely not doing pitch and yaw when it's coming in for re-entry well actually no we're patrolling on three axis all the time now technically you only need three fins to control on three axis but

54:42you can also roll if you need to change your yawn roll 90° pitch well the Control Authority you need is much more in Pitch than in any of the other axes like the amount of Control Authority you need for roll is practically nothing right and but but for for pitch you've got to basically push the booster down so you're going to push this monster thing into the wind and it doesn't want to go there y so the amount of pitch Force you need that's like the where you need the most amount of force y so having the having the two pairs of fins like closer together like more like an X-Wing Fighter allows them to contribute more in Pitch yep which then allows more

55:22Glide or more more of the airframe hitting the the sides of the bo booster you care about like how much force do you have relative to how much force you need in a given axis okay so you need a lot of force in the pitch axis so that's where you want to bias your grip pins yep yep you could arguably say they should be biased even closer together than they are currently yeah but this is a reasonable guess in between yeah

55:49well cuz this so this might end up pitching over more than the Falcon 9 cuz the Falcon 9 pitches pretty hard but it's skinnier and of course has less control Authority with with the 90° thing so maybe this could pitch even more and and arrest more of its velocity actually you you got various

56:07things that are better some things that are better some things that are worse you you you can leave it like like an airplane like an ampage where you've got a Rudder A Rudder and an elevator and if your elevator is far away from your center of mass then the amount of force you need is less to to change the angle like just think of it like a seesaw yeah you got a seesaw and or a wrench and if you have a long wrench it's easier to turn than a short wrench yep so if you have a shorter booster

56:39a short booster is harder to turn than a then a longer booster if you're depending on on where the control surface is relative to your center of mass okay the center of mass is the is the kind of the where the Seesaw like it's sees seawing around that Center Mass okay and Center pressure you got two things basically it's like it basically this sounds it sounds more complicated than is it's basically a teer toter or SEO that's where there's a center of pressure and a center of mass and it's going to basically just rotate around that yep and so if you've

57:17got a long stage that where the grid fins are far away from your center of mass then you need less Force to of to turn it to turn it yep so basically gotcha gotcha that makes sense Mak yeah if like a really St short stuby thing it would actually be quite hard to move it to move it yeah but the at least as far as the finest ratio this has a lot more potential since it's wider to to actually use atmospheric use the atmosphere to slow down before it even has to light its engines cuz like you know how new new Glenn has those strakes on the side and it looks like they're really planning to almost you know fly the thing for a little bit you know at a pretty high angle of attack

57:59compared to the relative Windstream to really let the atmosphere slow down the vehicle as much as possible you know you guys have a pretty compared to Falcon 9 is a lot finer or a lot less fine ratio it seems like you get a a lot more lift out of the thing realistically this is going to come in at something close to terminal velocity right oh yeah so yeah yeah cuz it you're trying to get to a precise point so it's very difficult to do a fast pitch up maneuver and and also get caught by the tower right like if you got a very big landing area that's then you could do that maybe but if you want to pring right over you can't do like a sudden pitch up at the end and then you

58:47got sort of pretty big moments of inosa here like this big things don't move like small things right so like you don't see a super tanker dashing around like speedboat right this is like in rocket form of a sub tanka so it doesn't move fast it's like it's a like way bigger than a whale yeah so yeah yes it is so it's it's it's just not going to move fast although ironically liftoff will be weirdly fast yeah but

59:21yeah yeah big rotating things always move slower than small rotating things you know yeah so it's it's yeah like I said yeah there there's a lot of potential improvements I mean yeah man oh man wasn't that an awesome conversation now in part three we're going to be taking you down to the Launchpad and you're going to be able to see Elon just walking around at work it's super fascinating again thank you Elon for spending so much time hanging out with me I'm glad that you had fun and it looks like maybe we'll be able to do this again you know I'm game for that and SpaceX thank you so much for allowing me to share all this awesome stuff with everyone but I owe a huge

1:00:22thank you to my patreon supporters for helping make this and everything we do here everyday astronaut possible if you want to gain access to some exclusive live streams and also our awesome Discord Community where we talk about everything spaceflight all the time head on over to patreon.com Everyday astronaut and while you're online be sure and check out our awesome Web Store where you'll find shirts like this the full flow stage combustion cycle shirt and the hoodie and the AOS Spike shirt and the rest of the schematics collection or the future Martian collection you'll find lots of fun stuff at everyday astronaut. comom sshop than thanks everybody that's going

1:00:56to do it for me I'm Tim Dodd the everyday astronaut bringing space down to earth for everyday people [Music]

资源与出处

相关视频

同频道、同主题或相邻年份